- 您现在的位置：买卖IC网 > Sheet目录350 > PG-FP4-E (Renesas Electronics America)PROGRAMMER FLASH MEMORY UNIV
CHAPTER 4 PG-FP4 OPERATION USING GUI SOFTWARE
[Disable Boot block cluster reprogramming check box]
If this check box is checked, the boot area is set regarding the boot block set by the Boot block cluster setting
function as the last block.
Caution
Be aware that if the security flag is set in the target device, writing to the boot area in the
device cannot subsequently be enabled.
The following is the correspondence between the Erase and Program commands when the security functions
of a single-power-supply flash memory microcontroller are valid.
CHIP Erase
Command
Block Erase
Command
Program Command
Read Command
Disable Chip Erase
Invalid
Invalid
Valid
Note1
Valid
Disable Block Erase
Disable Program
Disable Read
Valid
Valid
Valid
Invalid
Invalid
Valid
Valid
Invalid
Valid
Valid
Valid
Invalid
Disable Boot block
Invalid
Valid
Note 2
Valid
Note 2
Valid
cluster reprogramming
Note1.
2.
Since the Erase command is invalid, the data that differs from the data already written in the flash
memory cannot be written.
Valid only for an area not specified as the boot area.
<4> Program download/upload
The PG-FP4 has 2 MB of flash memory as a user program area.
This memory area can be used as a single 2 MB area, or as two independent 1 MB areas (Area 0 and Area
1).
Different user programs can be downloaded to Area 0 and Area 1, and it can be selected which of the
programs is to be written to the target device.
Figure 4-32. Setup Window – Program Download/Upload
[Enable two Program Areas check box]
If this check box is not checked, one 2 MB memory area is used as the user program area.
If it is checked, one of two independent 1 MB memory areas (Area 0 and Area 1) are used as the user
program area. For which area is to be used, refer to the [Programmer] → [Select Programming area…]
menu.
If a user program that exceeds 1 MB is downloaded, the error message “F410 Download failed” appears.
User’s Manual U15260EJ4V0UM
65
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PG15S-D20-HHB9
MOTOR GEARED STEPPER 15MM 15V BI
PG164120
PROGRAMMER MCU PICKIT 2
PG20L-D20-HHC0
MOTOR GEARED STEPPER 20MM 10V BI
PG25L-D24-HHC1
MOTOR GEARED STEPPER 25MM 24V BI
PG35S-D48-HHC2
MOTOR GEARED STEPPER 35MM 24V BI
PIC12F683 DEVELOPMENT KIT
KIT DEV EMBEDDED C
PIC18F4520 DEVELOPMENT KIT
KIT DEV EMBEDDED C
PIC18F67J10 DEVELOPMENT KIT
KIT DEV EMBEDDED C
相关代理商/技术参数
PG-FP5
制造商:Renesas Electronics Corporation 功能描述:MCU,Programmer,NEC Flash MCU
PG-FP5-AS
制造商:Renesas Electronics Corporation 功能描述:MICROCOMPUTER FLASH MEMORY PROGRAMMER 制造商:Renesas Electronics Corporation 功能描述:PROGRAMMER FLASH RL78 V850 7
PG-FP5-EA
功能描述:PROGRAMMER FLASH MEMORY UNIV RoHS:是 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:* 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:*
PGFP-A11
功能描述:PLUG GFCI 120VAC 15/20A AUTORST RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041
PGFP-A110KYST2
功能描述:CORD GFCI 120VAC 2' YEL SNG TAP RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041
PGFP-A110KY-ST2
制造商:Airpax 功能描述:
PGFP-A110KYST25
功能描述:CORD GFCI 120VAC 25' YEL SNG RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041
PGFP-A110KYTT2
功能描述:CORD GFCI 120VAC 2' YEL TRITAP RoHS:是 类别:过电压，电流，温度装置 >> 接地故障电路断路器 (GFCI) 系列:PGFP 标准包装:1 系列:PGFI 类型:带 6 英尺引线的直列接头 技术规格:120V 其它名称:723-1041